Happymodel Cine8 kit
Popis
Kit je snadno sestavitelný a nevyžaduje pájení. Kit obsahuje 3D printy. Verze přijímače: SPI Frsky (kompatibilní s ACCST D8/D16)
SPECIFIKACE:
Brand Name: Happymodel
Item Name: Cine8
Wheelbase: 85mm
Velikost: 145mmx140mmx23mm
Váha: 73g(bez baterie)
Obsah balení:
| Item Name | Qty |
| Cine8 Frame | 1 |
| 3D print TPU Insta360 go fixing mount for CINE8 | 1 |
| Option1: CrazyF411 PRO SPI Receiver version compatible FrskyD8/D16 S-FHSS | 1 |
| Happymodel EX1202.5 KV8000 brushless motor | 4 |
| Gemfan D51(2020-4) Cinewhoop Props | 1 |
| Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera | 1 |
| 5.8G 0mw~400mw OVX306 based on OpenVTX | 1 |
| TypeC USB Adapter | 1 |
| Tattu 3S 11.4V 450mah battery | 1 |
Specifikace dílů:
| Motor | Mode: EX1202.5 KV8000 Configu-ration:9N12P Stator Diamter:12mm Stator Length:2.5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ14mm*14.5mm Weight(g):4.4g No.of Cells(Lipo):2-3S |
| Propellers | Material:PC Weight:0.91g Pitch:2in Props Dia:50.3mm Center Thickness:4.5mm Center Hole Dia:1.5mm 3 holes |
| Flight controller | (Frsky SPI RX version) CrazyF411 PRO AIO FC Firmware target: MATEKF411RX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: BMI270 or ICM20689(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 7V-17V) Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5V 1A BEC |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 20A continuous peak 25A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_8.HEX Default protocol: DSHOT600 |
| Onboard Frsky SPI D8 receiver Version | CC2500 Hardware Compatible with FrskyD FrskyX Frsky_X_LBT SFHSS REDPINE protocol Channels: 8ch Failsafe support Diversity 2.4G receiver system No ground interference: above 300meter |
| External Flysky Fli14+ receiver | Channel: 14 Protocol: AFHDS-2A 2.4G Mode: The second generation of an enhanced version of the automatic FM digital system Antenna Length: 50mm (single antenna) Input Power: 4.0-6.5V DC Weight: Only 1g Size: 19.5mm*12mm*5mm Color: Black Signal Output: IBUS RSSI Output: Channel14 No ground interference: >500m |
| External Speki+ receiver | Dimension: 20mm*12.4mm*5mm Support protocol: DSM2/DSMX Output Signal configuration: SRXL(Set Spektrum2048/SRXL for the serial receiver provider) Antenna connector: I-PEX MHF3 Antenna length: 70mm Input voltage: 3.6v~13v Input current: 100ma Channels: Max12ch(usually channel 12 is used for RSSI) |
| External TBS CRSF Nano receiver | Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible |
| 5.8G 400mw VTX | Output power: 25mw~400mw switchable Frequency: 40CH Input voltage: 5V Current consumption: 400mA(type) Frequency: 5.8GHz 6bands 48 channels With Race bandSmartAudio ready |
| Caddx ANT 1200tvl camera | Image Sensor: 1/3″ CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: 0.001Lux@F1.2 Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.) |
| Lipo Battery | Capacity:450mAh Voltage:11.1v Continuous Discharge Rate: 75C Size: 66mmx21mmx18mm Weight: 45g Connector: XT30 |
Buďte první, kdo napíše příspěvek k této položce.
Přidat komentář