Mobeetle6
Popis
SPECIFIKACE:
Brand Name: Happymodel
Item Name: Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer Drone
Rozteč: 65mm
Velikost: 80mm*80mm*30mm
Váha: 17.5g (bez baterie)
hlavní body:
Nejlehči whoop na trhu
Součástí balení je karbonový rám na přestavbu whoopa na toothpick
Prémiový AIO board DiamondF4
Nové Unibell SE0702 brushless motory
Obsah balení:
| Item Name | Qty |
| 65mm whoop rám (Mobula6 frame) | 1 |
| 65mm toothpick rám (Mobeetle6 frame) | 1 |
| Volitelné: DiamondF4 ELRS built-in SPI ELRS receiver | 1 |
| Volitelné: DiamondF4 FR built-in SPI FRSKY receiver | |
| SE0702 KV23000 Unibell brushless motor | 4 |
| Gemfan 1210 31mm propeller(4cw+4ccw) | 1 |
| Runcam Nano3 | 1 |
| Built-in 5.8G 48ch 25mw-400mw OPENVTX | 1 |
| 1s 300mah Lipo battery | 2 |
| Mobula6 canopy | 1 |
| Propeller disassemble tool | 1 |
| Screwdriver | 1 |
Specifikace dílů:
| Motor | Mode:SE0702 KV23000 Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.5g No.of Cells(Lipo):1S only |
| Propeller | Weight:0.19g Material:PC Pitch:1 inchProps Dia:30mm Center Hole Dia:1mm |
| Flight controller | (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280 (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G OPEN VTX Built-in SPI ELRS V2.0/Frsky receiver Built-in 5V 1A BEC |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_50_REV16_8.HEX Default protocol: DSHOT600 |
| Onboard SPI ExpressLRS 2.4GHz Receiver | Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2.0 RF Frequency: 2.4GHz Antenna : Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2.0 TX Module Couldn’t flash separately ExpressLRS firmware |
| Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 modelChannels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
| Onboard 5.8g OPENVTX | Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw) |
| Runcam Nano3 | Model: RunCam Nano 3 Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL Lens : 2.3mm(M6.5) FOV 140° Signal System: NTSC S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: 0.01Lux@1.2F D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 110mA@5V 120mA@3.3V Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mm |
| Lipo Battery | Capacity:300mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 57mmx12mmx7mm Weight: 7.5gConnector: PH2.0 |
Související produkty
-
HAPPYMODEL_BATTERY_250MAH_1S
-
HAPPYMODEL_BATTERY_300MAH_1S
Buďte první, kdo napíše příspěvek k této položce.
Přidat komentář